Only logged in customers who have purchased this product may leave a review.
4 Channels Wireless Remote Control 315MHz -Arduino Compatible
₦ 3,000
- Communicate with Arduino over long distances
- 315MHz operating frequency
- Distance: approx. 50 Meters in open air
- 5V operation
- 4 Control channels
5 in stock
Related Products
-
NRF 240LO1+ 2.4GHz Wireless Transciever
₦ 950Quick View- Capable of up to 2Mbps communication
- 1.9 to 3.6V Operating Voltage
- Low – Power Features 400nASleep mode current consumption
- Fast start up time: 240us from SLEEP to RX or TX mode
- 1.9 to 3.6V Operating Voltage
Qucik View -
A6 GSM & GPRS Module
₦ 8,500Quick ViewA module that supports dual-band GSM/GPRS network, available for GPRS and SMS. Comes ready to keep your project connected via phone calls, SMS, or the Internet.
- Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz
- Working voltage: 4.5~5.5V DC (On-board voltage regulator circuit supply power for A6 module)
- Working current: maximum of 2A
- Sleep current: 5mA
- Onboard Micro SIM card holder, you can install Micro SIM card
- Onboard Micro USB interface for external power supply
- Communication Interface: TTL serial port
- Baud rate: 115200bps and it can also be set by AT command.
- Interface logic voltage: 3.3V
- Make and answer phone calls using a headset and electret microphone.
- Send and receive SMS messages.
- Send and receive GPRS data (TCP/IP, HTTP, etc.)
Qucik View -
Dual USB Output 9V 12V 24V 36V 5V DC-DC Power Supply Module
₦ 1,500Quick View- This is a mini DC-DC step down voltage converter module with fixed 5V voltage output.
- Input: 6V-40V
- Output: 5V / 3A (MAX)
- Efficiency: 92% (MAX)
- Switching frequency: 150KHZ
- Working temperature: -40 ‘C – + 85 ‘C
Qucik View -
Wi-Fi Module Serial to USB Adapter Board ESP8266
₦ 1,500Quick ViewThis USB ESP8266 adapter board which can be plugged directly to your computer allowing communication, testing and programming to be done on the module with ease.
· CH340 serial chip
· 3225 chip crystal, to enhance the stability of the serial port
Fully compatible with Windows, Mac and Linux systems
Qucik View -
3V to 5V USB Output Charger Step up Power Module
₦ 1,000Quick ViewThis module is used as a DC-DC booster, converting 3V to 5V. With the aid of this board, you can charge your mobile phones and power other kinds of USB devices from power sources with voltage as little as 1.5V such as batteries.
- Non-isolated step-up module (BOOST)
- Input voltage: 1-5V
- Output voltage: 5.1-5 .2 V
- Output Current: Rated 1A-1.5A
- Efficiency: Up to 96% (the higher the input voltage, the higher the efficiency)
- Switching frequency: 500KHz
- Output ripple: 30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
- Voltage indication: LED lights with load (input voltage less than 2.7V LED indicator off)
- Operating Temperature: Industrial (-40°c to +85°c)
- Full load temperature rise: 30°c
- Quiescent Current: 130uA
- Load regulation: ± 1%
- Voltage regulation: ± 0.5%
- Dynamic response speed: 5% 200uS
- Short circuit protection: None (Please use the lithium battery with protection.)
Qucik View -
Solid State Relay Module – SSR 40DA
₦ 5,000Quick ViewA solid state relay (SSR) allows you to control high-current AC loads from lower voltage DC control circuitry. Solid state relays have several advantages over mechanical relays. One such advantage is that they can be switched by a much lower voltage and at a much lower current than most mechanical relays. Also, because there’s no moving contacts, solid state relays can be switched much faster and for much longer periods without wearing out.
This particular SSR can switch current loads of up to 40A with a 3-32V DC input and a zero cross trigger control method. Each one of these relays is equipped with four screw terminals (for use with ring or fork connectors) and a plastic cover that slides over the top of the relay to protect the terminals.
Qucik View
Reviews
There are no reviews yet.