Only logged in customers who have purchased this product may leave a review.
20 X 4 LCD Module – Arduino Compatible
- You cannot add "Ethernet Module - ENC28J60" to the cart because the product is out of stock.
20 X 4 LCD Module – Arduino Compatible
₦ 8,250
This 20 X 4 LCD Module allows you to fit in a lot more text than you can on the smaller 16X4. It is however fully compatible. It has the industry standard HD44780 LCD controller.
-
- 20X4 Characters
- 5V Operating voltage
- Fully pin and code compatible with 16X2, 16X1 LCDs
- Backlight
Related Products
-
0 out of 5
Ethernet Module – ENC28J60
₦ 10,000This module allows you to add Ethernet connectivity to your projects. Based on the popular Microchip’s ENC28J60, this module will easily interface with any Microcontroller or Arduino board allowing Internet Connectivity via the Ethernet..
- Up to 10Mbps
- 5V Tolerant I/O pins
- Fully IEEE 803.2 Standards compatible
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
MQ-135 Air Quality/Pollution Sensor – Arduino Compatible
₦ 3,500The MQ-135 air quality and pollution sensor detects hazardous gases such as benzene, alcohol, smoke, CO2, NH3 and NOx(Nitrous Oxides) in the air. Analog out put can be interfaced directly to ADC of a microcontroller.
- 5V Operation.
- High sensitivity and response time.
Sample Applications: This sensor can be used to build air quality sensing devices for indoor and outdoor applications)
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
L298 H-Bridge Motor Driver – Arduino Compatible
₦ 4,000Basic attributes
Module name :Dual H-bridge motor driver module
Operating mode :H-bridge driver (dual)
Master chip :L298NLogic voltage :5V
Drive voltage :5V-35V
Logic Current :0mA-36mA
Drive current :2A (MAX single bridge)
Storage Temperature :-20 to 135Maximum Power :25W
Weight :30gExternal dimensions :43 * 43 * 27mmProduct added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Pulse Sensor -Arduino Compatible
₦ 6,000This pulse sensor measure heart rate by simly being in contact with a finger or earlobe.
- 3-5V Operation
- Pulse Sensor Board
- Coded Cable with Standard Male Headers
For a tutorials and sample code, visit: //pulsesensor.com/pages/code-and-guide
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
SCT-013 Non-invasive 100A Current Transformer (CT) -Arduino Compatible
₦ 11,750This current transformer allows you to easily measure to current running through a wire without tampering with the setup, simply pass the wire through or open up and clip around the wire.
Can be used for any of the following applications: Measurment and protection circuits, AC motors, lighting, air compressors, remote monitoring, Energy meters,etc
Features:
- Measures up to 100A
- Core material: ferrite
- Non-linearity 3%(10%-120% rated input current)
- 1.5m leading wire, with 3.5mmplug standard output.
- Two form of output current, voltage (voltage output built-in the burden resistor).
- Opening size:13mmx13mm
- Safety indicators: Dielectric strength 6000V AC/1min
- Meet UL94-V0 flame retardant properties
- Operating Temperature: -25 C ~ +70 C
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View -
0 out of 5
Arduino Nano
₦ 9,750The Arduino Nano is a full featured breadboard-friendly Arduino board. It is based on an Atmega 328 microcontroller. Fully programmable with Arduino IDE
Key Features:
- 5V Operating Voltage
- 7-12 Volt Unregulated Supply Voltage
- 8 Analog Input Pins
- 14 Digital I/O Pins
- 32kB Flash Memory (2kB Bootloader)
- 1kB RAM
- 512 Bytes EEPROM
- UART
- SPI
- PWM
Product added! Browse WishlistThe product is already in the wishlist! Browse WishlistQucik View
Reviews
There are no reviews yet.